Troubleshooting Tips for P80 Lower Parts Kit Installation

Are you having trouble installing a p80 lower parts kit? Don’t worry, you’re not alone! Many gun enthusiasts struggle with the installation process and find it to be a difficult task. In this blog post, we will be providing troubleshooting tips to help you complete the installation of your p80 lower parts kit successfully.

Tools and Materials Needed

To install a P80 lower parts kit, there are a few essential tools and materials you’ll need to have on hand. These include:

  • A workbench or flat surface: It’s important to have a stable work surface to assemble your lower receiver and avoid any accidents.
  • A set of punches and a hammer: Punches and hammers will help you tap pins and push out parts from the P80 lower parts kit.
  • A pair of needle-nose pliers: These are useful for reaching small spaces and gripping small parts during assembly.
  • A torque wrench: This tool is crucial for properly tightening bolts and screws to prevent over-tightening or stripping.
  • A small container or tray: A small container or tray will help you keep track of small parts during assembly.
  • Lubricant: You’ll need some type of lubricant, like gun oil, to apply to parts during assembly and ensure smooth operation.
  • A P80 lower parts kit: Of course, you’ll need the actual P80 lower parts kit itself, which should come with all of the necessary parts and pieces for assembly.

By having all of these tools and materials ready before you start your P80 lower parts kit installation, you’ll be well-prepared to tackle any challenges that may arise during assembly.

Step by Step Instructions

  • Begin by thoroughly reading the instructions that come with your P80 lower parts kit. If you do not have the instructions, you can usually find them online at
  • Make sure you have all the necessary tools and materials, including a punch set, pliers, and a vise.
  • Start by installing the trigger housing into the frame, making sure it is seated properly.
  • Install the trigger assembly and hammer into the frame, following the manufacturer’s instructions carefully.
  • Install the slide stop and magazine release, making sure they are properly aligned and seated.
  • Install the locking block and rear rail assembly.
  • Install the pins, springs, and other small components as necessary.
  • Finally, test the functionality of your completed P80 lower parts kit by dry firing and inspecting the trigger reset.

By following these step-by-step instructions and using the resources available at, you can successfully install your P80 lower parts kit. Remember to take your time, pay close attention to the instructions, and be patient. Happy building!

Tips and Tricks

As with any gun part installation, there are always a few tricks and tips to make the process go smoother. Here are a few tips that can help you when you’re working with your P80 lower parts kit.

  • Take Your Time: This is especially important if you’re new to gun building. Rushing through the process can result in mistakes and misalignments that can lead to malfunctioning firearms. So, take your time, double-check your work, and ensure everything is installed properly before moving on.
  • Use the Right Tools: Investing in the right tools can make a huge difference in the installation process. A few must-haves include a vise block, armorer’s wrench, torque wrench, and roll pin punches. These tools are available on sites like, and will save you time and frustration.
  • Keep Things Organized: When you’re working with a lot of small parts, it’s easy to misplace or mix things up. Keeping your workspace organized with labeled trays, small parts bins, and magnetic trays will help ensure everything stays in its place.
  • Use a Pin Punch Starter: The roll pins used in the P80 kit can be tough to get started, especially if you’re working in tight spaces. Using a pin punch starter can make the process easier and help prevent the pins from bending or getting stuck.
  • Test Everything Before You Finish: Before you finalize your build, be sure to test everything out. Ensure all your safety mechanisms are working properly, and the trigger is operating as expected. This is also a good time to ensure the slide locks back and the magazine releases smoothly.

With these tips in mind, you’ll be well on your way to completing your P80 lower parts kit installation with confidence and ease. And, don’t forget to check out for all your gun building needs.